Installation Kit Video Module and TV Amplifier for TV Function together with Installation Kit for On-Board Monitor and Navigation BMW 5 Series (E39)

EBA – 01 29 0 007 858
BMW Installation Instructions

Supplementary Sheet to Installations Instructions Installation Kit for Video Module and TV Amplifier for TV Function in Conjunction with Installation Kit for On-Board Monitor and Navigation BMW 5 series (E39), order No.: 01 29 0 007 858

Installation Kit Video Module and TV Amplifier for TV Function together with Installation Kit for On-Board Monitor and Navigation BMW 5 Series (E39)

The installation kit on-board monitor and navigation must be installed first before installing the installation kit video module and TV amplifier forTV function.

Contents

  1. Important Information
  2. Installation

1. Important Information

Intended for use in BMW dealership network only.

Specialised knowledge is required.

Installation time required 1.5 hours

The installation time may vary depending on the condition and equipment of the vehicle. The installation kit on-board monitor and navigation must be installed first before installing the installation kit video module and TV amplifier for TV function.

Target group

These installation instructions are intended for specialist personnel trained in BMW passenger cars and who independently carry out all maintenance, repair, installation and readjustment jobs on passenger cars. All jobs are to be c arried out with the aid of valid B MW

  • Repair instructions
  • Schematic circuit diagrams
  • Maintenance manuals
  • Working instructions– Diagnosis manuals in rational order with the specified tools (special tools) and in compliance with valid health and safety regulations.

Installation notes

Knowledg e of vehicle electrical systems is required.

Safety notes

Particular care must be taken when installing cables/lines to ensure they are not kinked, bent or damaged. Additionally installed cables/lines must be secured with cable ties.

Necessary tools and aids

Set of 1/4 inch socket wrenches
Side cutter
Set of screwdrivers for cross-head screws
Inspection lamp
Set of screwdrivers for slotted-head screws

2. Installation

Contents 

    1. Parts Overview
    2. Installation of TV Amplifier and Video Module
    3. Encoding

2.1 Parts Overview

Installation Kit Video Module and TV Amplifier for TV Function together with Installation Kit for On-Board Monitor and Navigation BMW 5 Series (E39)

Item Description Qty.
1 Video module 1
2 TV amplifier, right 1
3 TV amplifier, left 1
4 Light-gauge self-tapping screw with serrated washer M5x12 2
5 Hexagon screw with washer M5x14 1
6 Speed nut M5 1

Continue with Section 2.2

2.2 Installation of TVAmplifier and Video Module

Notes

Refer to general information as well as safety notes in Section 1.

Preparation

Print out fault code memory
Disconnect battery
Remove rear bench seat
Remove rear seat backrest
Remove left and right C-pillar trim panel
Remove rear window shelf
Open rear left luggage compartment trim panel
Remove navigation computer

Fig. A

Installation Kit Video Module and TV Amplifier for TV Function together with Installation Kit for On-Board Monitor and Navigation BMW 5 Series (E39)

Firmly secure TV amplifier on left (3) to mounting point (7) provided on left-hand C-pillar with M5x12 light-gauge
self-tapping screw with serrated washer (4).
Plug in existing, tied-back coaxial pin housing (8) at left-hand TV amplifier (3) and firmly tighten screws.
Release existing plug connection (9).
Connect black 1-pin socket contact (10) from left-hand TV amplifier (3) to black 1-pin pin contact (11) from released plug connection (9).
Connect black 1-pin pin contact (12) from left-hand TV amplifier (3) to black 1-pin socket contact (13) from released plug connection (9).

Fig. B

Installation Kit Video Module and TV Amplifier for TV Function together with Installation Kit for On-Board Monitor and Navigation BMW 5 Series (E39)

Firmly secure TV amplifier on right (2) to mounting point (14) provided on right-hand C-pillar with M5x12 light-gauge self-tapping screw with serrated washer (4).
Plug in existing, tied-back coaxial pin housing (15) at right-hand TV amplifier (2) and firmly tighten screws.
Release existing plug connection (16).
Connect black 1-pin socket contact (17) from right-hand TV amplifier (2) to black 1-pin pin contact (18) from released plug connection (16).
Connect black 1-pin pin contact (19) from right-hand TV amplifier (2) to black 1-pin socket contact (20) from released plug connection (16).

Fig. C

Installation Kit Video Module and TV Amplifier for TV Function together with Installation Kit for On-Board Monitor and Navigation BMW 5 Series (E39)

Fit M5 speed nut (6) on mounting bracket for video module, front (21).
Fit video module (1) on retaining studs (22) of basic carrier (23) and firmly secure on mounting bracket for video
module, front (21) with M5x14 hexagon screw and washer (5).

Fig. D

Installation Kit Video Module and TV Amplifier for TV Function together with Installation Kit for On-Board Monitor and Navigation BMW 5 Series (E39)

Pass blue 18-pin socket housing (24) through mounting bracket for navigation computer (25) towards rear and route to video module (1).
Release the two tied-back, angled coaxial socket housings (26, 27) and the tied-back white 18-pin socket
housing (28) and route to video module (1).
Release tied-back blue 18-pin socket housing (29) (to be connected at navigation computer).

Fig. E

Installation Kit Video Module and TV Amplifier for TV Function together with Installation Kit for On-Board Monitor and Navigation BMW 5 Series (E39)

Connect blue 18-pin socket housing (24) to blue 18-pin pin housing (30) at video module (1).
Connect white 18-pin socket housing (28) to white 18-pin pin housing (31) at video module (1).
Connect the two angled coaxial socket housings (26, 27) to the two coaxial pin housings (32, 33) at video module (1).

Fig. F

Installation Kit Video Module and TV Amplifier for TV Function together with Installation Kit for On-Board Monitor and Navigation BMW 5 Series (E39)

Connect bordeaux 18-pin socket housing (34) to bordeaux 18-pin pin housing at navigation computer (35).
Connect blue 18-pin socket housing (29) to blue 18-pin pin housing at navigation computer (35).
! Take particular care to ensure that the cables and lines are not trapped or damaged behind the
navigation computer.
Now fit navigation computer (35) in mounting bracket for navigation computer (36) and close rear left luggage
compartment trim panel.

Concluding jobs

Reconnect battery
Carry out function check
Print out fault code memory
Reassemble vehicle in reverse order of removal

Continue with Section 2.3

2.3 Codierung

Hinweise
Allgemeine Hinweise sowie Sicherheitshinweise in Kapitel 1 beachten.
Dieses System ist codierrelevant.
Damit das Nachrüstsystem:
– in vollem Umfang funktionsfähig ist und
– im Verbund mit den anderen elektrischen Fahrzeugsystemen Fehlfunktionen und Störungen ausschließt, muß
eine Codierung dieses Nachrüstsystems und gegebenenfalls weiterer Fahrzeugkomponenten durchgeführt und
im zentralen Codierschlüssel der IKE gespeichert werden.
Diese Codierung wird automatisch mit dem jeweils aktuellen Codierprogramm im Pfad „Nachrüstung“
durchgeführt.
Der Ablauf ist bedienergeführt, es sind die jeweiligen Texthinweise bei der Durchführung der einzelnen Schritte zu
beachten.
Vorgehensweise:
– DIS/MoDiC an das Fahrzeug anschließen
– Zündung „EIN“
– Auswahl „Codierung ZCS“
– Eingabe Datum mit „Y“bestätigen (nur bei MoDiC)
– Baureihe:„E39“
– Pfad:„2 Nachrüstung“
– System:„7 Navigation“
Zum Laden des Betriebsystems wird eine „Navigations CD-ROM Betriebssoftware“benötigt.
Achtung! CD-ROM „Betriebssoftware“noch nicht in das CD-Laufwerk einlegen! CD-ROM „Betriebssoftware“erst
einlegen, wenn es in den Hinweisen am Bordmonitor beschrieben wird.
Gleichzeitig wird mit dieser CD-ROM „Betriebssoftware“die Sprachcodierung durchgeführt.
– Automatische Codierung starten (mit „Y“bestätigen)
– Den Hinweisen am Bordmonitor folgen.
– Neues Zentraletikett vom geänderten Codierschlüssel ausdrucken und am Fahrzeug im Gepäckraum rechts
im Bereich der Batterie aufkleben.
– Nach dem Hinweis „Codierung beendet“am Bildschirm vom DIS/MoDiC, Zündung „AUS“, mindestens
10 Sekunden warten und anschließend wieder Zündung „EIN“.
– Fehlerspeicher ausdrucken
– CD-ROM „Straßenkarte“ in den Navigationsrechner einschieben.
– Funktionsprüfung durchführen
Bei Fahrzeugen mit DSP-Verstärker muß zusätzlich der DSP-Verstärker neu codiert werden.
Vorgehensweise:
– DIS/MoDiC an das Fahrzeug anschließen
– Zündung „EIN“
– Auswahl „Codierung ZCS“
– Eingabe Datum mit „Y“bestätigen (nur bei MoDiC)
– Baureihe:„E39“
– Pfad:„1 Neucodierung“
– System:„82 DSP“
– Automatische Codierung starten (mit „Y“ bestätigen)
– Nach dem Hinweis „Codierung beendet“am Bildschirm vom DIS/MoDiC, Zündung „AUS“, mindestens
10 Sekunden warten und anschließend wieder Zündung „EIN“.
– Fehlerspeicher ausdrucken
– Funktionsprüfung durchführen
Sprachcodierung
Die Sprachcodierung kann erneut über die „Navigations CD-ROM Betriebssoftware“durchgeführt werden.

banner