BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

EBA – 01 29 0 138 842
BMW Installation Instructions

BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

These installation instructions are only valid for cars with SA 640

The installation time is approx. 2 hours, but this may vary depending on the condition of the car and the equipment in it.

Retrofit / Installation kit No.

84 63 0 029,319
84 63 0 139 857

Contents

Section

Important information
1. Preparations
2. Installation and cabling diagram
3. Connection diagram
4. To install and connect the hands-free control module
5. To install and connect the eject box
6. To install the hands-free microphone
7. Concluding work and coding

Important information

This upgrade kit is for use within the BMW dealership organisation only.

Target group

The target group for these installation instructions is specialist personnel trained on BMW cars with specialist knowledge of vehicle electrical systems.

Work:

All servicing, repair and installation work on BMW cars is completed at your own risk. All work is to be carried out using current BMW

– Repair manuals – Circuit diagrams

in a rational order using the prescribed tools (special tools) and observing current health and safety regulations.

Ordering instructions

Centre console insert

A black insert for the centre console is supplied in the upgrade kit.

An insert for the centre console in other colours for cars with different interior colours can be ordered if required. See the EPC for all further ordering information.

Safety instructions

The current accident prevention regulations must be followed.

Refer to the safety instructions for handling components of the airbag system. Further information is available in the TIS in RA No. 32 34 … If you fail to follow the safety instructions the airbag system may deploy incorrectly and cause injuries.

List of pictograms and special equipment

Denotes information that must be read before the installation work for safety reasons and to avoid damaging the car.

->Denotes instructions that draw your attention to special features.

The following special equipment must be taken into consideration when installing the upgrade kit. The various sections contain corresponding information.

SA 401 Tilt and slide sunroof

1.Preparations

TIS instruction No.
Conduct a brief test
Disconnect the negative pole of the battery 12 00 …
The following components must be removed first of all:
Boot lid trim on the left 51 47 172
Fresh air grille in the rear 64 22 190
Armrest (no longer required)
Hands-free microphone trim

2.Installation and cabling diagram

BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

Legend

  1. Hands-free microphone
  2. Eject box and interface
  3. Adapter eject box
  4. Hands-free control module
  5. Hands-free control module adapter

3.Connection overview

BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

Item Description Signal Cable colour/

Crosssection

Connection location in the car Abbreviation /

Slot

A Adapter eject box Between the standard wiring harness and interface
A1 Black 18-pin plug To interface X4545
A2 Black 18-pin plug To plug X4545 on the standard wiring harness X4545
B Hands-free control module adapter Between the standard wiring harness and hands-free control module
B1 Black 54-pin plug To plug X13599 on the standard wiring harness X10616
B2 Black 25-pin plug To hands-free control module X13324
B3 Black 3-pin plug To aerial amplifier X1765

4.To install and connect the hands-free control module

BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

[1] Insert the hands-free control module (1) into the holder (2) and secure it with the bar (3).

Connect branch B2 to the hands-free control module (1).

BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

Bolt the holder with the hands-free control module (1) to the body stud (3) on the left-hand side of the boot using hexagonal screws (2).

BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

Release the tied back, black 54-pin plug X13599 from the standard wiring harness.Connect branch B1 to plug X13599.

5.To install and connect the eject box

BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

[2] Clip the eject box (1) into the armrest (2).

BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

Place the slide plate (1) on the armrest (2) and secure it with Philips screws (3).

BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

Bolt the holder (1) for the interface to the centre console (2) with Philips screws (2).

BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

Connect the black 12-pin plug (1) for the eject box to the interface (2).Insert the interface (2) into the holder (3).

BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

Connect the black 6-pin plug (1) for the eject box to the black 6-pin plug (2) for the interface.

Connect the aerial cable (3) for the eject box to the standard aerial cable (4).

BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

The adapter cable A must be fitted.”

Connect the adapter cable A between the black 18-pin plug for the interface and plug X4545 on the standard wiring harness.

6.To install the hands-free microphone

Cars without SA 401 only

BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

Release the tied back plug X4221 from the standard wiring harness and connect it to the hands-free microphone (1).

The arrow on the hands-free microphone (1) must point to the front of the car.”

Clip the hands-free microphone (1) into the trim (2).

Cars with SA 401 only

BMW Motorola V50 / V3690 (dual band) hand-free upgrade kit BMW 5 Series Saloon (E39)

Release the tied back plug X4221 from the standard wiring harness and connect it to the hands-free microphone (1).

The arrow on the hands-free microphone (1) must point to the front of the car.”

Clip the hands-free microphone (1) into the trim (2).

7.Concluding work and coding

This upgrade system does not require coding.”

  • Conduct a brief test with DIS/MoDiC.
  • Conduct a function test
  • Assemble the car again following the instructions to dismantle it in reverse order.

If necessary, the circuit diagram for the telephone preparation (SA 640) and for the adapter cables can be taken from the installation instructions entitled “Telephone upgrade circuit diagrams, part No. 01 29 0 140 378” on the installation instructions CD.”

banner