Rev counter retrofit kit MINI (R50)

EBA – 01 29 0 138 899
Mini Installation Instructions
Rev counter retrofit kit MINI (R50)

The installation time is approx. 1.5 hours, but this may vary depending on the condition of the car and the equipment in it.

Retrofit kit: 62 11 0 030 110

Contents

Section

Important information
1. Preparations
2. Parts list
3. Installation and cabling diagram for retrofit wiring harness
4. Rev counter wiring harness connection overview
5. To install and connect the rev counter wiring harness
6. To install the rev counter
7. Concluding work
8. Coding
9. Rev counter circuit diagram

Important information

The retrofit kit is only for use within the dealership organisation.

Do not kink or damage the cables during the installation work since otherwise they may cause faults that can later only be identified by extensive additional work. The costs incurred as a result of this will not be reimbursed.

If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used.

Target group

The target group for these installation instructions is specialist personnel trained on MINI cars with specialist knowledge of vehicle electrical systems.

Work:

All servicing, repair and installation work on MINI cars is completed at your own risk. All work is to be carried out using current MINI

– Repair manuals – Circuit diagrams

in a rational order using the prescribed tools (special tools) and observing current health and safety regulations.

Required tools and equipment

Set of flat screwdrivers
Set of Philips screwdrivers
Torch
1/4 inch socket set
1/4 inch Torx socket set
Angle cutter
Combination pliers

1.Preparations

TIS instruction No.
Disconnect the negative pole of the battery 12 00 …
The following components must be removed first of all:
Oddments box on the driver’s side
Top instrument panel cover
Tachometer instrument panel
Top and bottom steering column trims

2.Parts list

Rev counter retrofit kit MINI (R50)

Legend

  1. Rev counter wiring harness A
  2. Steering column rev counter
  3. Cover
  4. Torx screws (2x)

3.Installation and cabling diagram for retrofit wiring harness

Rev counter retrofit kit MINI (R50)

Legend

  1. Rev counter wiring harness A
  2. Steering column rev counter
  3. Tachometer instrument panel

4.Rev counter wiring harness connection overview

Rev counter retrofit kit MINI (R50)

Item Description Signal Cable colour / Cross-section Connection location in the car Abbreviation / Slot
A Rev counter wiring harness A
A1 Green 7-pin socket casing To steering column rev counter X11176
A2 Socket contact Terminal 58g GR/RT 0.35 mm2 To tachometer instrument panel X11175

PIN 2

A3 Socket contact CAN H GE/SW0.5 mm in diameter To black 12-pin plug on the tachometer instrument panel X11175

PIN 12

A4 Socket contact CAN L GE/BR0.5 mm in diameter To black 12-pin plug on the tachometer instrument panel X11175

PIN 6

A5 Socket contact TRIP BR0.35 mm in diameter To black 12-pin plug on the tachometer instrument panel X11175

PIN 8

A6 Socket contact V battery BL0.35 mm in diameter To black 12-pin plug on the tachometer instrument panel X11175

PIN 7

A7 Socket contact Terminal 31 BR/SW0.35 mm in diameter To black 12-pin plug on the tachometer instrument panel X11175

PIN 1

5.To install and connect the rev counter wiring harness

Rev counter retrofit kit MINI (R50)

Lay wiring harness A as follows and secure it with cable ties:
– Branch A1 to the installation site of the rev counter on the steering column
– Branches A2 – A7 to the tachometer instrument panel (1)

Rev counter retrofit kit MINI (R50)

Connect branches A2A7 as follows to plug X11175 :
A2 GR/RT cable, PIN 2
A3 GE/SW cable, PIN 12
A4 GE/BR cable, PIN 6
A5 BR cable, PIN 8
A5 BL cable, PIN 7
A7 BR/SW cable, PIN 1
Connect plug X11175 to the instrument cluster I (1).

6.To install the rev counter

Rev counter retrofit kit MINI (R50)

[1] Place the cover (1) on to the steering column rev counter (2) as shown.

Refit the top and bottom steering column trims.

Rev counter retrofit kit MINI (R50)

Connect branch A1, green 7-pin plug X11176, to the steering column rev counter (1).

Rev counter retrofit kit MINI (R50)

Screw the steering column rev counter (1) to the steering column using the Torx screws (2) provided.

7.Concluding work

  • Connect the battery
  • Complete the coding work (see section entitled “Coding”)
  • Conduct a function test
  • Assemble the car again following the instructions to dismantle it in reverse order.

8.Coding

Retrofitting the steering column rev counter requires coding and must be coded using the “Retrofit rev counter” path using the MoDiC/DIS.

The coding work must be completed using CD version 26.0 (or higher).

After the coding procedure disconnect the car’s battery for at least 10 seconds, then reconnect it and conduct a function test.

9.Rev counter circuit diagram

Rev counter retrofit kit MINI (R50)

Legend

A2 Tachometer instrument panel
A9001 Steering column rev counter
X11175 Tachometer instrument panel
X11176 Steering column rev counter

Cable colours

BR brown
GE yellow
SW black
RT red
GR grey
BL blue

banner