Alarm system retrofit kit MINI (R50, R53) LHD and RHD

EBA – 01 29 0 139 734
Mini Installation Instructions
Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Technical and electrical knowledge required

Installation time approx. 3 -4 hours, which can vary according to the condition of the car and the equipment in it.

Retrofit kit:
65 75 0 029 310 (LHD)
65 75 0 139 732 (RHD)

Contents

Section

1. Important information for the installation of the alarm system
2. Preparations
3. Parts list
4. LHD connection diagram
5. RHD connection diagram
6. Installation and cabling diagram (LHD cars)
7. Installation and cabling diagram (RHD cars)
8. To install the ultrasonic sensor in the headlining in cars with a sunroof
9. To install the ultrasonic sensor in the headlining in cars without a sunroof
10. To install the alarm system connection cable (LHD cars)
11. Coding and concluding work
12. Function test
13. Circuit diagram

1. Important information for the installation of the alarm system

Only for use in the MINI dealer organisation.

The alarm system wiring harness may only be installed by a specialist workshop that has the required special tools and manuals (servicing, repair, diagnostics, etc.).

Ensure that the cables/lines are not kinked or damaged as you install them in the car.Additional cables/lines that you install must be secured with cable ties/textile adhesive tape.

Item numbers refer only to the overview drawings and to the texts next to the appropriate figure.

The alarm system connection cable A is only required for LHD cars, the alarm system connection cable B is only required for RHD cars.

Required tools and equipment

Set of Allen keys Set of flat screwdrivers
Set of Torx sockets Cable lamp
1/4 inch socket set Angle cutter
Set of 1/2 inch socket wrenches Carpet knife
Cable lamp

2. Preparations

TIS instruction No.
Print out error memory
Disconnect the battery 12 00 …
Remove the rear seat bench
Remove the rear seat backrest
Remove the side trim at the rear left
Remove the door sill strips on both sides
Remove the C pillar covers on both sides
Remove the B pillar trims on both sides
Remove the SHD frame at the front and rear
Remove the handles at the rear left and right
Remove the ceiling light at the rear
Release the rear headlining
Remove the cover on the instrument panel
Remove oddments box on the driver’s side
Remove the tachograph
Remove the steering column trims at the top and bottom
Remove the wiper switch
Release the fuse holder

3. Parts list

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Legend

A Alarm system connection cable (LHD cars)
B Alarm system connection cable (RHD cars)
1 Wiper switch
2 Tilt alarm sensor
3 Emergency-current siren
4 Emergency-current siren holder
5 Ultrasonic module
6 Ultrasonic interior guard trim (must be ordered separately)
7 Bottom ultrasonic module holder
8 Top ultrasonic module holder
9 Hexagonal screw M6x16 (2x)
10 Hexagonal screw with washer M6x12
11 Cable tie (20x)
12 Black 4-pin plug for the alarm system siren (required for the alarm system siren)
13 Hexagonal nut M6 (2x)
14 5 A fuse
15 Template (supplied with the parts kit)

4. LHD connection diagram

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Item Description Signal Cable colour

/ Crosssection

Connection location in the car Abbreviation /

Slot

A Alarm system connection cable (LHD cars)
A1 Blade terminal contact Terminal 31L BR To alarm system siren X19562, PIN1
A2 Blade terminal contact STDWA SW/RT/GE To alarm system siren X19562, PIN2
A3 Blade terminal contact Terminal 30 RT/SW/GE To alarm system siren X19562, PIN3
A4 Blade terminal contact Siren SW/BL/WS To alarm system siren X19562, PIN4
A5 Blade terminal contact DWAL GR/SW/GE To wiper switch socket casing X10692, PIN9
A6 Blade terminal contact Terminal 30 RT/SW/GE Fuse holder input XVII X110207, PIN11
A7 Cable eyelet Terminal 31L BR To earth post left X1108
A8 Cable eyelet Terminal 31E BR/SW To E earth post left X13230
A9 Black 4-pin socket casing To radio interior guard X1582
A10 Black 6-pin socket casing To DWA tilt sensor at the rear left X1222
A11 Blade terminal contact DWAL GR/SW/GE Base module on socket casing D X255, PIN14
A12 Blade terminal contact Siren SW/BL/WS Base module on socket casing B X253, PIN11
A13 Blade terminal contact Terminal 30 SW/GE Base module on socket casing B X253, PIN15
A14 Blade terminal contact DWA12V RT/SW Base module on socket casing B X253, PIN16
A15 Blade terminal contact STDWA SW/RT/GE Base module on socket casing B X253, PIN27
A16 Blade terminal contact NG SW/BL Base module on socket casing B X253, PIN30
A17 Blade terminal contact DWA12V SW/RT Base module on socket casing B X253, PIN34

5. RHD connection diagram

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Item Description Signal Cable colour /

Cross-section

Connection location in the car Abbreviation /

Slot

B Alarm system connection cable (LHD cars)
B1 Blade terminal contact Terminal 31L BR To alarm system siren X19562, PIN1
B2 Blade terminal contact STDWA SW/RT/GE To alarm system siren X19562, PIN2
B3 Blade terminal contact Terminal 30 RT/SW/GE To alarm system siren X19562, PIN3
B4 Blade terminal contact Siren SW/BL/WS To alarm system siren X19562, PIN4
B5 Blade terminal contact DWAL GR/SW/GE To base module socket casing D X255, PIN14
B6 Blade terminal contact Terminal 30 RT/SW/GE Fuse holder input XVII X110207, PIN11
B7 Cable eyelet Terminal 31L BR To earth post left X1108
B8 Cable eyelet Terminal 31E BR/SW To E earth post left X13230
B9 Black 4-pin socket casing To radio interior guard X1582
B10 Black 6-pin socket casing To DWA tilt sensor at the rear left X1222
B11 Blade terminal contact DWAL GR/SW/GE To wiper switch plug X10692, PIN9
B12 Blade terminal contact Siren SW/BL/WS To base module socket casing B X253, PIN11
B13 Blade terminal contact Terminal 30 SW/GE To base module socket casing B X253, PIN15
B14 Blade terminal contact DWA12V RT/SW To base module socket casing B X253, PIN16
B15 Blade terminal contact STDWA SW/RT/GE To base module socket casing B X253, PIN27
B16 Blade terminal contact NG SW/BL To base module socket casing B X253, PIN30
B17 Blade terminal contact DWA12V SW/RT To base module socket casing B X253, PIN34

6. Installation and cabling diagram (LHD cars)

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

All the wiring harnesses are to be laid along the main wiring harness as shown in the figure and secured with cable ties.

Alarm system wiring harness

Branches A1-A4 to alarm system siren

Branch A5 to wiper switch socket casing X10692

Branch A6 to fuse holder plug X10207

Branch A7 to left earth post X1108

Branch A8 to left E earth post X13230 Branch A9 to radio interior guard

Branch A10 to the tilt sensor at the rear left

Branch A11 to base module D socket casing X255

Branches A12-A17 to base module B socket casing X253

Point X cable passage at the rubber grommet on the driver’s side branches A1-A4

Tie back any excess lengths.

7. Installation and cabling diagram (RHD cars)

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

All the wiring harnesses are to be laid along the main wiring harness as shown in the figure and secured with cable ties.

Alarm system wiring harness

Branches B1-B4 to alarm system siren

Branch B5 to base module D socket casing X255 Branch B6 to fuse holder plug X10207 Branch B7 to left earth post X1108

Branch B8 to left E earth post X13230

Branch B9 to radio interior guard

Branch B10 to the tilt sensor at the rear left

Branch B11 to wiper switch socket casing X10692

Branches B12-B17 to base module B socket casing X253

Point X cable passage at the rubber grommet on the driver’s side branches B1-B4

Tie back any excess lengths.

8. To install the ultrasonic sensor in the headlining in cars with a sunroof

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Place the template (15) on the raised area in the centre of the headlining (30).

Dimension a = 560mm

Dimension b = 560mm

Dimension c = 75mm

Affix the template and cut it out with a carpet knife.

Refer to the direction of the arrow.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Ensure that you install it in the correct direction, the arrow on the top of the

installation frame must point to the front of the car.

Insert the top section of the installation frame (7) into the cut-out in the headlining from above.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Ensure that you install it in the correct direction, the arrow on the bottom of the

installation frame (8) must point to the front of the car.

Lock the installation frame (8) inserted from the bottom to the top section (7).

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

The arrows on the ultrasonic module (5) and the cover (6) must point to the front of the car.

Clip the ultrasonic module (5) into the cover (6).

9. To install the ultrasonic sensor in the headlining in cars without a sunroof

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Dimension b = 235mm
Dimension c = 50mm

Affix the template and cut it out with a carpet knife.

Refer to the direction of the arrow.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Ensure that you install it in the correct direction, the arrow on the top of the

installation frame must point to the front of the car.

Insert the top section of the installation frame (7) into the cut-out in the headlining from above.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Ensure that you install it in the correct direction, the arrow on the bottom of the

installation frame (8) must point to the front of the car.

Lock the installation frame (8) inserted from the bottom to the top section (7).

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

The arrows on the ultrasonic module (5) and the cover (6) must point to the front of the car.

Clip the ultrasonic module (5) into the cover (6).

10. To install the alarm system connection cable (LHD cars)

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Branch A9/B9 comes from the tilt alarm sensor installation site and is laid along the left C pillar upwards to the ultrasonic module (5).

Connect branch A9/B9 black 4-pin plug to the ultrasonic module (5).

Check the installation direction.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Connect branch A10/B10 black 6-pin socket casing to the tilt alarm sensor (2).

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Rear left near the tail light.

Secure the tilt alarm sensor (2) with two hexagonal screws M6x16 (9).

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Left side skirt.

Secure the cable eyelet A7/B7 to the earth bolt X1108.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Left side skirt.

Secure the cable eyelet A8/B8 to the E earth bolt X13230.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Fuse holder on the A pillar at the left.

Connect the violet 12-pin fuse holder socket casing X10207 branch A6/B6, blade terminal contact, red/black/yellow cable, to PIN11. Check that there is a fuse in fuse slot F24. If not insert a 5 A fuse (14).

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Plan view of dashboard.

Lay branches A12-A17, A11/B12-B17, B5 along the standard wiring harness above the dashboard.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Wiper switch connection plug.

Connect the black 10-pin wiper socket casing X10692 branch A5/B11, blade terminal contact, grey/black/yellow cable, to PIN9.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Install the new wiper switch (1). Connect the black 10-pin wiper switch socket casing (30).

The removed wiper switch is no longer required.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Base module on the right A pillar.

To the black 54-pin socket casing X253 from base module B. Connect branch A12/B12, blade terminal contact, black/blue/white cable, to

Connect branch A13/B13, blade terminal contact, black/yellow cable, to PIN15.

Connect branch A14/B14, blade terminal contact, red/black cable, to PIN16.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Base module on the right A pillar.

To the black 54-pin socket casing X253 from base module B. Connect branch A15/B15, blade terminal contact, black/red/yellow cable, to

Connect branch A16/B16, blade terminal contact, black/blue cable, to PIN30.

Connect branch A17/B17, blade terminal contact, black/red cable, to PIN34.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Base module on the right A pillar.

To the blue 54-pin socket casing X255 from base module D. Connect branch A15/B5, blade terminal contact, grey/black/yellow cable, to PIN14.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

The figure shows LHD.

Proceed in the same way on RHD cars.

Cut open the rubber grommet.

Lay branches A1-A4/B1-B4 through the cable grommet on the driver’s side.

Seal the rubber grommet with sealing compound.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

The figure shows LHD.

Lay branches A1-A4 behind the bulkhead to the installation site of the alarm system siren (in the engine compartment on the right).

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

The figure shows RHD.

Lay branches B1-B4 behind the bulkhead to the installation site of the alarm system siren (in the engine compartment on the left).

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Connect the casing of the black alarm system siren socket casing (12) to the cable before inserting the pin.

To the black 4-pin alarm system siren socket casing (12)Connect branch A1/B1, blade terminal contact, brown cable, to PIN1. Connect branch A2/B2, blade terminal contact, black/red/yellow cable, to PIN2. Connect branch A3/B3, blade terminal contact, red/black/ yellow cable, to PIN3. Connect branch A4/B4, blade terminal contact, black/blue/white cable, to PIN4.

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Screw the alarm system siren (3) to the holder (4) using the hexagonal nut M6 (13).

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Connect the black 4-pin alarm system siren socket casing (12) to the siren (3).

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

The figure shows LHD.

Screw the alarm system siren and holder (30) using the hexagonal screw M6x12 (10) and hexagonal nut (13).

Proceed in the same way on RHD cars.

11. Coding and concluding work

Connect the battery.

This system requires coding.

To ensure that the retrofit system: – is fully functional and

  • prevents malfunctions and errors when combined with other electrical systems in the car, this retrofit system and, possibly, other components must be coded and saved in the central code of the IKE.

This coding process is automatic using the current coding program in the “Retrofit” path.The procedure is user-guided, follow the text instructions for completing each individual step.

Procedure

  • Connect DIS/MoDIC to the car
  • Ignition “ON”
  • Select “Coding ZCS”
  • Confirm the date by pressing “Y” (MoDIC only)
  • Series: “R50”
  • Path: “2 Retrofit”
  • System: “Alarm system”

Concluding work

Check the function of the alarm system (section 12) and assemble the car.

12. Function test

Procedure Response
1. Arm the alarm system with the remote key. The doors and boot are locked at the same time.
2. The hazard lights will flash once and the LED will start to flash quickly. All the doors, the bonnet and the boot are locked. The tilt alarm sensor is active.The ultrasonic module will be activated approx. 30 seconds later.
3. Brief acoustic signal from the emergency-current siren. The doors, the bonnet or the boot are not closed properly. The tilt alarm sensor is active.The ultrasonic module is not activated.
4. Open the doors, bonnet or boot. An acoustic alarm will be emitted for 30 seconds and an optical alarm for 5 minutes (depending on national version).
5. Trip the ultrasonic module approx. 1 minute after arming it by waving your hand through an open window An acoustic alarm will be emitted for 30 seconds and an optical alarm for 5 minutes (depending on national version).
6. Test the tilt alarm system by raising the car at one side when the alarm system has been armed. An acoustic alarm will be emitted for 30 seconds and an optical alarm for 5 minutes (depending on national version).
7. Test the emergency-current siren by disconnecting the car’s battery when the alarm system is armed. An acoustic alarm will be emitted.
8. Disarm the alarm system with the remote key. The doors and boot are unlocked at the same time.The LED will go out.

13. Circuit diagram

Alarm system retrofit kit MINI (R50, R53) LHD and RHD

Legend
X253 Base module B plug (black)
X255 Base module D plug (blue)
X1108 Earth post
X1222 Tilt alarm sensor plug
X1582 Interior guard plug
X10207 Fuse switch plug
X10692 Wiper switch plug
X13230 E earth post
X19562 4-pin alarm system siren plug

Cable colours
RT red
SW black
GN green
BR brown
GE yellow
WS white
VI violet
GR grey
BL blue
OR orange

banner