BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

EBA – 01 29 0 140 412
BMW Installation Instructions
BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

These installation instructions are only valid for cars with SA 640

The installation time is approx. 2.5 hours, but this may vary depending on the condition of the car and the equipment in it.

Retrofit / Installation kit No.

84 61 0 029 298
84 61 0 140 411

Contents

Section

Important information

  1. Preparations
  2. Installation and cabling diagram
  3. Connection diagram
  4. To install and connect the transceiver module
  5. To install and connect the eject box
  6. To install the hands-free microphone
  7. Concluding work and coding

Important information

This upgrade kit is for use within the BMW dealership organisation only.

Target group

The target group for these installation instructions is specialist personnel trained on BMW cars with specialist knowledge of vehicle electrical systems.

Work:

All servicing, repair and installation work on BMW cars is completed at your own risk. All work is to be carried out using current BMW

– Repair manuals – Circuit diagrams

in a rational order using the prescribed tools (special tools) and observing current health and safety regulations.

Ordering instructions

Centre console insert

A black insert for the centre console is supplied in the upgrade kit.

An insert for the centre console in other colours for cars with different interior colours can be ordered if required. See the EPC for all further ordering information.

Safety instructions

The current accident prevention regulations must be followed.

Refer to the safety instructions for handling components of the airbag system. Further information is available in the TIS in RA No. 32 34 … If you fail to follow the safety instructions the airbag system may deploy incorrectly and cause injuries.

The following special equipment must be taken into consideration when installing the upgrade kit. The various sections contain corresponding information.

SA 401 Tilt and slide sunroof

1. Preparations

TIS instruction No.
Conduct a brief test
Disconnect the negative pole of the battery 12 00 …
The following components must be removed first of all:
Left boot – wheel arch trim 51 47 151
Fresh air grille in the rear 64 22 190
Armrest (no longer required)
Hands-free microphone trim

2. Installation and cabling diagram

BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

Legend

  1. Hands-free microphone
  2. Eject box and interface
  3. Adapter eject box
  4. Transceiver module
  5. Transceiver module adapter

3. Connection overview

BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

Item Description Signal Cable colour

/ Crosssection

Connection location in the car Abbreviation /

Slot

A Adapter eject box Between the standard wiring harness and interface
A1 Black 18-pin plug To interface X4545
A2 Black 18-pin plug To plug X4545 on the standard wiring harness X4545
B Transceiver module adapter Between the standard wiring harness and transceiver module
B1 Black 54-pin plug To plug X13599 on the standard wiring harness X10616
B2 Black 25-pin plug To transceiver module X13324
B3 Black 3-pin plug To aerial amplifier X1765
C Aerial adapter Between the standard wiring harness and transceiver module
C1 FAKRA plug contact To standard aerial cable
C2 Mini UHF plug contact To transceiver module

4. To install and connect the hands-free control module

BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

[1] Insert the transceiver module (1) into the holder (2) and secure it with the bar (3).

BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

Bolt the holder with the transceiver module (1) to the body stud (3) on the left-hand side of the boot using hexagonal screws M5 (2).

BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

Connect branch B2 to the transceiver module (1).

Connect the aerial adapter C between the transceiver module (1) and standard aerial cable (2).

BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

Release the tied back, black 54-pin plug X13599 from the standard wiring harness.Connect branch B1 to plug X13599.

5. To install and connect the eject box

BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

[2] Clip the eject box (1) into the supplied armrest (2).

BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

Place the slide plate (1) on the armrest (2) and secure it with Philips screws (3).

BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

Bolt the holder (1) for the interface to the centre console (2) with Philips screws (2).

BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

Connect the black 12-pin plug (1) for the eject box to the interface (2).Insert the interface (2) into the holder (3).

BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

Connect the black 6-pin plug (1) for the eject box to the black 6-pin plug (2) for the interface.

BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

The adapter cable A must be fitted.

Connect the adapter cable A between the black 18-pin plug for the interface and plug X4545 on the standard wiring harness.

6. To install the hands-free microphone

BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

Release the tied back plug X4221 from the standard wiring harness and connect it to the hands-free microphone (1).

The arrow on the hands-free microphone (1) must point to the front of the car.

Clip the hands-free microphone (1) into the trim (2).

BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E39/2)

Release the tied back plug X4221 from the standard wiring harness and connect it to the hands-free microphone (1).

The arrow on the hands-free microphone (1) must point to the front of the car.

Clip the hands-free microphone (1) into the trim (2).

7. Concluding work and coding

This upgrade system does not require coding.

  • Conduct a brief test with DIS/MoDiC.
  • Conduct a function test
  • Assemble the car again following the instructions to dismantle it in reverse order.

If necessary, the circuit diagram for the telephone preparation (SA 640) and for the adapter cables can be taken from the installation instructions entitled “Telephone upgrade circuit diagrams, part No. 01 29 0 140 378” on the installation instructions CD.

banner