BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

EBA – 01 29 0 146 231
BMW Installation Instructions
BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

These installation instructions are only valid for cars with SA 640.

The installation time is approx. 2.5 hours, but this may vary depending on the condition of the car and the equipment in it.

Retrofit kit No. 84 63 144 314

Contents

Section

Important information

  1. Preparations
  2. Installation and cabling diagram
  3. Connection diagram
  4. To install and connect the transceiver module
  5. To install and connect the eject box
  6. To install the hands-free microphone
  7. Concluding work and coding

Important information

This upgrade kit is for use within the BMW dealership organisation only.

Do not kink or damage the cables during the installation work since otherwise they may cause faults that can later only be identified by extensive additional work. The costs incurred as a result of this will not be reimbursed by BMW.

Target group

The target group for these installation instructions is specialist personnel trained on BMW cars with specialist knowledge of vehicle electrical systems.

Work:

All servicing, repair and installation work on BMW cars is completed at your own risk. All work is to be carried out using current BMW

– Repair manuals – Circuit diagrams in a rational order using the prescribed tools (special tools) and observing current health and safety regulations.

Ordering instructions

Centre console insert

A black insert for the centre console is supplied in the upgrade kit.

An insert for the centre console in other colours for cars with different interior colours can be ordered if required. See the EPC for all further ordering information.

Special tools required

DIS or MoDiC

1. Preparations

TIS instruction No.
Conduct a brief test
Disconnect the negative pole of the battery 12 00 …
The following components must be removed first of all:
Left boot wheel arch trim 51 47 151
Fresh air grille in the rear 64 22 190
Armrest (no longer required)
Hands-free microphone trim

2. Installation and cabling diagram

BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

Legend

  1. Hands-free microphone
  2. Eject box and interface
  3. Adapter eject box
  4. Transceiver module
  5. Transceiver module adapter

3. Connection diagram

BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

Item Description Signal Cable colour / Crosssection Connection location in the car Abbreviation / Slot
A Adapter eject box Between the standard wiring harness and interface
A1 Black 18-pin plug To interface X4545
A2 Black 18-pin plug To standard wiring harness X4545
B Transceiver module adapter Between the standard wiring harness and transceiver module
B1 Black 54-pin plug To standard wiring harness X4038
B2 Black 25-pin plug To transceiver module X13324
C Aerial adapter Between the standard wiring harness and transceiver module
C1 FAKRA plug contact To standard aerial cable
C2 Mini UHF plug contact To transceiver module

4. To install and connect the hands-free control module

BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

[1] Insert the transceiver module (1) into the holder (2) and secure it with the bar (3).

BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

Bolt the holder with the transceiver module (1) to the body stud (3) on the left-hand side of the boot using hexagonal nuts M5 (2).

BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

Connect branch B2 to the transceiver module (1).

Connect the aerial adapter C between the transceiver module (1) and standard aerial cable (2).

BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

Release the tied back, black 54-pin plug X4038 from the standard wiring harness.Connect branch B1 to plug X4038.

5. To install and connect the eject box

BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

Clip the eject box (1) into the supplied armrest (2).

BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

Place the slide plate (1) on the armrest (2) and secure it with Philips screws (3).

BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

Bolt the holder (1) for the interface to the centre console (2) with Philips screws (2).

BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

Connect the black 12-pin plug (1) for the eject box to the interface (2).

Insert the interface (2) into the holder (3).

BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

Connect the black 6-pin plug (1) for the eject box to the black 6-pin plug (2) for the interface.

BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

The adapter cable A must be fitted.”

Connect the adapter cable A between the black 18-pin plug (1) for the interface and plug X4545 on the standard wiring harness.

6. To install the hands-free microphone

Cars with SA 401 only

BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

Release the tied back plug X4221 from the standard wiring harness and connect it to the hands-free microphone (1).

The arrow on the hands-free microphone (1) must point to the front of the car.”

Clip the hands-free microphone (1) into the trim (2).

Cars without SA 401 only

BMW Apollo / Car Phone Upgrade Kit BMW 5 Series touring (E39/2) from 03/02

Release the tied back plug X4221 from the standard wiring harness and connect it to the hands-free microphone (1).

The arrow on the hands-free microphone (1) must point to the front of the car.”

Clip the hands-free microphone (1) into the trim (2).

7. Concluding work and coding

This upgrade system does not require coding.”

  • Conduct a brief test with DIS/MoDiC.
  • Conduct a function test
  • Assemble the car again following the instructions to dismantle it in reverse order.

Refer the DIS (Diagnostic Information System) for the circuit diagram of the telephone preparation (SA 640), if required.

Refer to the telephone retrofit UNI II circuit diagrams, PN: 01 29 0 146 546 on the installation manual CD for the circuit diagrams of the adapter, if required.”

banner