TV function retrofit kit BMW 5 Series Saloon (E39)

EBA – 01 29 0 153 181
BMW Installation Instructions

These installation instructions are only valid for cars with SA 609 (navigation system)

Important information

The retrofit kit is for use within the BMW dealership organisation only. Subject to technical modifications.

Target group

The target group for these installation instructions is specialist personnel trained on BMW cars with the appropriate specialist knowledge.

All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and work instructions in a rational order using the prescribed tools (special tools) and observing current health and safety regulations.

Installation information

Ensure that the cables/lines are not kinked or damaged as you install them in the car.

The installed cables are to be secured with cable ties.

If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used. After the installation work the retrofit TV function must be coded using DISPlus, MoDiC III or GT-1 via the Retrofit path.

Information on operation

The TV function is only active when the car is at a standstill.

Installation time

Approx. 3,5 hours, but this may vary depending on the condition of the car and the equipment in it.

Retrofit kit No. 65 50 0 153 183

Special tools required

Set of installation wedges (009317)

Contents

Section

1. Preparations
2. Parts list
3. Connection diagram
4. Installation and cabling diagram
5. To install and connect the adapter and aerial cables
6. Concluding work
7. Circuit diagram

1.Preparations

TIS instruction No.
Refer to the safety instructions for handling components of the airbag system. 32 34 …
Conduct a brief test – – –
Disconnect the negative pole of the battery 12 00 …
The following components must be removed first of all:
Seat bench 52 24 005
Rear backrests, left and right 52 24 010
C pillar trim on the left and right 51 43 251
Rear window shelf 51 46 000
Boot floor trim 51 47 101
Boot trim on the left 51 47 151
Release the navigation computer 65 90 510

2.Parts list

TV function retrofit kit BMW 5 Series Saloon (E39)

Legend

A Adapter cable
B TV1 aerial cable
C TV2 aerial cable
D Video module
E Aerial booster, left
F Aerial booster, right
G Speed nut M5
H Hexagonal screw with washer M5 x 14
I Self-tapping screw (2x)
J Cable tie (10x)

3.Connection diagram

TV function retrofit kit BMW 5 Series Saloon (E39)

Item Description Signal Cable colour / Cross-section Connection location in the car Abbreviation / Slot
A Adapter cable
A1 18-pin BL socket casing To navigation computer A112 X1313
A2 18-pin BL plug casing To the plug on the standard wiring harness, 18-pin BL socket casing X1313
A3 18-pin BL socket casing To video module A197 X18804
A4 18-pin natural socket casing To video module A197 X18806
A5 Socket contact TVNF+ GE

0.5 mm2

To radio receiver N9

12-pin natural socket casing

X13648

PIN 11

A6 Socket contact TVNF- BL/GE 0.5 mm2 To radio receiver N9

12-pin natural socket casing

X13648

PIN 12

B TV1 aerial cable Between aerial booster on the left and video module A197
C TV2 aerial cable Between aerial booster on the right and video module A197

4.Installation and cabling diagram

TV function retrofit kit BMW 5 Series Saloon (E39)

Legend

A Adapter cable
B TV1 aerial cable
C TV2 aerial cable
D Video module
E Aerial booster, left
F Aerial booster, right
1 Radio receiver
2 Navigation computer

5.To install and connect the adapter and aerial cables

TV function retrofit kit BMW 5 Series Saloon (E39)

Place the speed nut G on the module holder (1).

Insert the video module D into the module holder (1) and secure it with a hexagonal screw H.

TV function retrofit kit BMW 5 Series Saloon (E39)

Connect branches A3 and A4 on the adapter cable A to the same coloured cables on the video module D.

Lay branches A5 and A6 to the radio receiver (1).

Disconnect the plug X18126 from the radio receiver (1).

Cars without a CD changer only

TV function retrofit kit BMW 5 Series Saloon (E39)

Connect branches A5 and A6 to the enclosed natural coloured plug X13648 as follows: – Branch A5, GE cable in PIN 11

– Branch A6, BL/GE cable in PIN 12

Connect plug X13648 to the free slot in plug X18126.

Cars with a CD changer only

Connect branches A5 and A6 to the existing plug X13648 as follows:

  • Branch A5, GE cable in PIN 11
  • Branch A6, BL/GE cable in PIN 12

All cars

Connect plug X18126 to the radio receiver.

TV function retrofit kit BMW 5 Series Saloon (E39)

Disconnect the blue plug X1313 on the navigation computer (1).

Connect the adapter cable A as follows to the navigation computer (1):

  • Branch A2 to plug X1313
  • Branch A1 to the navigation computer (1)

TV function retrofit kit BMW 5 Series Saloon (E39)

Connect the aerial cables TV 1 B and TV 2 C to the video module D and thread them through the grommet (1) into the passenger cabin.

TV function retrofit kit BMW 5 Series Saloon (E39)

Lay the aerial cable TV1 B to the left C pillar.

TV function retrofit kit BMW 5 Series Saloon (E39)

Lay the connection cable (2) for the aerial booster E under the gas lance (3) to the plug connector (1) for the rear screen aerial.

Open the plug connector (1) and connect the connection cable (2) for the aerial booster E.

Secure the aerial booster E to the existing hole in the C pillar using a screw I.

Connect the aerial cable TV1 B to the aerial booster E.

TV function retrofit kit BMW 5 Series Saloon (E39)

Lay aerial cable TV2 C under the insulation mat to the right C pillar.

TV function retrofit kit BMW 5 Series Saloon (E39)

Lay the connection cable (2) for the aerial booster F under the gas lance (3) to the plug connector (1) for the rear screen aerial.

Open the plug connector (1) and connect the connection cable (2) for the aerial booster F.

Secure the aerial booster F to the existing hole in the C pillar using a screw I.

Connect the aerial cable TV2 C to the aerial booster F.

6.Concluding work

  • Connect the battery
  • Encode the TV function using DISPlus, MoDiC III or GT-1 via path Retrofit
  • Conduct a function test
  • Re-assemble the car

7.Circuit diagram

TV function retrofit kit BMW 5 Series Saloon (E39)

Legend

A112 Navigation computer A197 Video module
N9 Radio receiver
O400 Screen open
O401 Screen open
X1313 18-pin BL socket casing on the navigation computer and 18-pin BL plug casing to the standard wiring harness
X13016 Terminal 31 connector
X13317 Terminal 30 connector
X13648 12-pin natural socket casing on the radio receiver
X18344 I bus connector
X18804 18-pin BL plug on the video module
X18806 Natural coloured 18-pin plug on the video module
Y1* 18-pin BL socket casing on the standard wiring harness

All designations with an asterisk (*) only apply to these installation instructions and this circuit diagram.

Cable colours

BL blue
BR brown GE yellow
GN green
RT red
SW black
WS white

banner