CD-6 Changer in Conjunction with “Bavaria C Professional RDS” HI-Fl System for BMW 5 Series E34/2 Touring

EBA – 01 29 9 786 788
BMW Installation Instructions

CD-6 Changer in Conjunction with "Bavaria C Professional RDS" HI-Fl System for BMW 5 Series E34/2 Touring

Specialised knowledge is required.

Installation time is approx . 2 to 3 hours, though this may vary according to condition and fittings of vehicle.

General notes

Instructions and illustrations are given for left-hand drive mo­ dels. For right-hand drive models, work stages should be car­ ried out in mirror-image fashion .

Drillings should be removed completely , bore holes burred and inorganic zinc applied.

Newly installed metal parts and areas impaired as a result of welding (new cavities, seams, grooves etc.) must be sealed with a BMW-approved preservative .

Tools and materials required

Phillips screwdriver
Regular screwdriver
Torx screwdriver T10
Side cutting pliers
Universal knife
Open-jawed spanner , A/F 10 mm
Ratchet with 1/2″ drive
1/2″ extension
1/2″ drive socket, A/F 10 mm, 17 mm

Contents

Chapter

  1. Vehicle preparation and removal operations
  2. Long control unit/CD changer connecting lead
  3. Installing CD changer
  4. Connecting CD changer

1. Vehicle preparation and removal operations

  1. Print out fault memory
  2. Remove rear seat bench and backrest
  3. Disconnect battery
  4. Remove left panel in luggage compartment
  5. Remove centre console
  6. Remove rear left entrance strip
  7. Remove connecting lead for control unit/receiver

2. Long control unit/CD changer connecting lead

F 34 65 480

CD-6 Changer in Conjunction with "Bavaria C Professional RDS" HI-Fl System for BMW 5 Series E34/2 Touring

Feed white connector (1) of control unit/CD changer connec­ ting lead through installation aperture of control unit to centre channel. Connect rectangular angle connector to control unit.

F 34 65 481

CD-6 Changer in Conjunction with "Bavaria C Professional RDS" HI-Fl System for BMW 5 Series E34/2 Touring

Lay connecting lead (1) along and to rear of centre channel and guide it under carpet at point indicated by arrow in illus­ tration .

F 34 65 566

CD-6 Changer in Conjunction with "Bavaria C Professional RDS" HI-Fl System for BMW 5 Series E34/2 Touring

Pull back carpet and guide connecting lead (1) under cable cover (2) to seat base.

F 34 65 567

CD-6 Changer in Conjunction with "Bavaria C Professional RDS" HI-Fl System for BMW 5 Series E34/2 Touring

Remove split rivet (1).

Lay connecting lead under moulded part (2) on left seat base as far as luggage compartment.

Rub soap into rubber grommet.

3. Installing CD changer

F 34 65 593

CD-6 Changer in Conjunction with "Bavaria C Professional RDS" HI-Fl System for BMW 5 Series E34/2 Touring

Set installation position of CD changer by adjusting screws located on side of changer.

Unscrew securing screws (1). Turn adjusting screws (2) in one of directions indicated by arrows in the illustration .

V = vertical installation
H = horizontal installation

Tighten securing screws (1).

F 34 65 601

CD-6 Changer in Conjunction with "Bavaria C Professional RDS" HI-Fl System for BMW 5 Series E34/2 Touring

Pull away insulating mat from side panel and use two Phillips screws (3) to screw each bracket (1 and 2) onto side panel. Remove pre-marked surface of floor insulating mat (4).

F 34 65 605

CD-6 Changer in Conjunction with "Bavaria C Professional RDS" HI-Fl System for BMW 5 Series E34/2 Touring

Use Phillips screws (3) to secure interface (2) to bracket (1). Attach connector holder (4) and cable clips (5).

F 34 65 606

CD-6 Changer in Conjunction with "Bavaria C Professional RDS" HI-Fl System for BMW 5 Series E34/2 Touring

Use Phillips screws (3) to secure bracket (1) to the CD chan­ ger (2). Screw 14-pin connector (4) of interface (5) onto 14- pin socket (6) of CD changer (2) and secure with cable clips .

F 34 65 607

CD-6 Changer in Conjunction with "Bavaria C Professional RDS" HI-Fl System for BMW 5 Series E34/2 Touring

Use Phillips screws (3) to secure CD changer (1) to bracket (2).

4. Connecting CD changer

F 34 65 608

CD-6 Changer in Conjunction with "Bavaria C Professional RDS" HI-Fl System for BMW 5 Series E34/2 Touring

Attach white connector (1) of short receiver/interface connec­ ting lead (3) to receiver (2) and lay connecting lead (3) as far as interface.

F 34 65 609

CD-6 Changer in Conjunction with "Bavaria C Professional RDS" HI-Fl System for BMW 5 Series E34/2 Touring

Connect black connector (6) of the short receiver/interface connecting lead (with “CD-Wechsler” tag) to black interface socket (4). Connect white connector (5) of long control unit/in­ terface connecting lead (with “CD-Wechsler” tag) to white in­ terface socket (4).

Connect tied-back connector (1) of radio wiring harness to

CD changer (3) socket (2) and push into connector holder (7).

F 34 65 592

CD-6 Changer in Conjunction with "Bavaria C Professional RDS" HI-Fl System for BMW 5 Series E34/2 Touring

Remove adhesive strip, pin (1) and Phillips screws (2). Co­ ver bore holes with adhesive patches (3).

Instructions for CO changer are included in operation instruc­ tions for radio.

Carry out an operational check.

According to vehicle fittings , left-hand luggage compartment panel must be ordered separately .

Reinstall all removed parts in reverse sequence.

banner