X
    Categories: Ski Bag

Ski Bag BMW 5 Series E34

EBA – 01 29 9 787 597
BMW Installation Instructions

Tools and materials required

1/2″ drive socket, NF 10 mm, 17 mm
1/2″ extension
Ratchet with 1/2″ drive
Torque wrench
Hammer
Flat chisel
Inorganic zinc paint
Paint brush
Half-round file
Universal knife
Regular screwdriver
Phillips screwdriver

Contents

Chapter

  1. Removing Rear-Seat Bench and Backrest
  2. Cutting Insulating Mat to Size
  3. Preparing Rear Panel for Ski-Bag Installation
  4. Assembling Ski Bag
  5. Converting Centre-Arm-Rest Attachment
  6. Installing Centre Arm Rest

1. Removing Rear-Seat Bench and Backrest

F 34 65 036

Lift out and remove rear-seat bench (1) from mounting bracket in direction of arrows in illustration.

F 34 65 037

Fold down rear centre arm rest.

Pull up and remove shaft panelling and Velcro-type fastener from centre arm rest. Remove plastic hexagon nuts (1) for backrest and hexagon bolts (2) for seat belt.

F 34 65 001

Fold back insulating mat (1) and remove plastic nuts (2) on right and left of backrest.

F 34 72 132

Remove plastic covers (1) for safety belts in direction of arrows in illustration. Lift up backrest from brackets, pull forward and remove.

F 32 72 028

Remove luggage-compartment mat. Remove plastic nuts (1) with a regular screwdriver and remove panelling (2). This panelling (2) is now no longer required.

2. Cutting Insulating Mat to Size

F 32 72 023

Cut out insulating mat (1) along pre-cut line (2) with universal knife.

3. Preparing Rear Panel for Ski-Bag Installation

F 32 72 029

Press out plastic plugs (1, 2).

F 32 72 030

Separate connecting points (1) of pre-stamped intermediate panelling (2) from rear partition panelling (3) with a flat chisel.

F 32 72 031

Burr and align metal edge (1) of ski-bag opening (2) and coat bare areas of metal with inorganic zinc paint.

4. Assembling Ski Bag

F 34 72 001

Separate plastic frame (1) at its connecting points (2) by levering out retaining lugs and pull apart in direction of arrows in illustration.

F 32 72 033

Fit plastic frame (1) to ski-bag case (2) as shown in illustration and snap retaining lugs (3) into place.

F 32 72 034

Secure new luggage-compartment panelling (1, 2) to rear partition panelling (3) with plastic nuts (4).

F 32 72 039

Snap retaining lugs (3, 4) of ski-bag case (1) into openings of rear partition panelling (2).

Note

Install ski-bag case from luggage-compartment side.

5. Converting Centre-Arm-Rest Attachment

F 34 72 002

Remove Phillips screws (1) from centre arm rest on left and right.

F 34 72 003

Remove left and right plastic covers (1) of centre arm rest.

F 34 72 004

Remove nut (1) from pin (2) on left and right and remove bracket (3).

F 34 72 005

Install new bracket (1) and centre arm rest (2) with nut (3). Fit plastic covers.

Vehicles with modified centre arm rest

F 34 72 133

Remove securing screws (1) on both sides of centre arm rest (2) and remove bracket (3).

F 34 72 134

Secure (supplied) bracket (1) to centre arm rest (2) with Phillips screws (3).

F 34 72 006

Screw on retaining bracket (1) to backrest with countersunk-head screws (2).

Note

Reinstall the backrest and rear-seat bench in reverse sequence

6. Installing Centre Arm Rest

F 34 72 007

Insert retaining lugs (1) into guide (2). Press back centre arm rest and snap lock (3) into place in retaining bracket (4).

Secure shaft panelling with Velcro-type fastener. Fold up centre arm rest into final position.

eba :
Disqus Comments Loading...

This website uses cookies.