Installation kit for bracket for 1 kg / 1.3 kg dry-chemical fire extinguisher BMW Z3 roadster (E36/7)

EBA – 01 29 9 789 901
BMW Installation Instructions
Installation kit for bracket for 1 kg / 1.3 kg dry-chemical fire extinguisher BMW Z3 roadster (E36/7)

Technical knowledge is required.

Installation time approx. 1 hour, which can vary according to the conditions and fittings of the vehicle.

Note

The extinguisher incl. bracket may be mounted only on the driver’ s seat. If mounted on the passenger seat it is possible that a malfunction of the front-passenger airbag may occur.

Required tools

Screwdriver
1/4 inch extension
3/8 inch ratchet
3/8 inch socket-wrench insert SW 13 mm, SW 16 mm
Hammer
Drill machine
Carpet knife
1/4 inch ratchet
1/4 inch socket-wrench insert SW 10 mm
3/8 inch extension
Torque spanner
Prick punch
Drill Ø = 6.5 mm

1. Necessary preparatory work

Dismantle driver’s seat.

Caution

If nee. deactivate buckle pre-tensioner.

For guidance in this, use your workshop documents.

2. Fit bracket

F 36 82 803 ZS

Installation kit for bracket for 1 kg / 1.3 kg dry-chemical fire extinguisher BMW Z3 roadster (E36/7)

Bend up the gripping spikes (1) in area of the right seat guide-rail (2) and the gripping spikes (3) and draw seat cover (4) over the seat bucket.

F 36 82 804 ZS

Installation kit for bracket for 1 kg / 1.3 kg dry-chemical fire extinguisher BMW Z3 roadster (E36/7)

Fasten bracket (1) to the bead (2) of the seat bucket (arrows), positioning it in such a way that the extension of the centre line of the bead (3) lines up with the centre of the drill hole (4). Mark the hole (4) on the seat bucket, prick-punch and drill to a diameter of 6.5 mm.

F 36 82 805 ZS

Installation kit for bracket for 1 kg / 1.3 kg dry-chemical fire extinguisher BMW Z3 roadster (E36/7)

Put retaining plate (1) with short side in the direction of travel (arrow) in the seat bucket (2) (insert set screws in the boreholes). Position upholstery in the seat bucket (2) again and pull the seat cover (3) over the seat bucket (2) and secure with the gripping spikes.

F 36 82 806 ZS

Installation kit for bracket for 1 kg / 1.3 kg dry-chemical fire extinguisher BMW Z3 roadster (E36/7)

Cut apertures (arrows) in the seat cover for the two set screws (3).

Using nuts (2) screw bracket (1) on to the two set screws (3).

Tightening torque of the nuts (2) = 10 NM.

3. Fit fire extinguisher

1 kg extinguisher only

F 36 82 807 ZS

Installation kit for bracket for 1 kg / 1.3 kg dry-chemical fire extinguisher BMW Z3 roadster (E36/7)

Insert retaining strap (1) in the extinguisher holder (2) with the guide pin (arrow) and secure with screws (3) to the bracket (4).

Tightening torque of the screws (4) = 10 NM.

F 36 82 808 ZS

Installation kit for bracket for 1 kg / 1.3 kg dry-chemical fire extinguisher BMW Z3 roadster (E36/7)

Place extinguisher (1) in the support and secure with the retaining strap (2).

1.3 kg fire extinguisher only

F 36 82 809 ZS

Installation kit for bracket for 1 kg / 1.3 kg dry-chemical fire extinguisher BMW Z3 roadster (E36/7)

Fasten fire-extinguisher holder (1) and metal brace (2) to the bracket (4) with screws (3).

Tightening torque of the screws (3) = 10 NM.

F 36 82 810 ZS

Installation kit for bracket for 1 kg / 1.3 kg dry-chemical fire extinguisher BMW Z3 roadster (E36/7)

Place fire extinguisher (1) in the support (2) and secure with the retaining strap (3).

Fit the driver’s seat back into the vehicle.

Note

Carry out the dismounting and mounting of the driver’ s seat (incl. tightening torque) in accordance with the repair instructions.

F 31 82 021

Installation kit for bracket for 1 kg / 1.3 kg dry-chemical fire extinguisher BMW Z3 roadster (E36/7)

Stick the sticker as required in a suitable place, e.g. on the inside lower right of the front passenger side­ window.

banner