Navigation System Japan BMW 5 Series E39

EBA – 01 29 9 790 070
BMW Installation Instructions

Navigation System Japan BMW 5 Series E39

(Only intended for use in BMW dealership network (HO)).

Installation time approx. 1 – 2 hours which can vary

depending on condition and equipment of vehicle. Knowledge of vehicle electrical system is required.

Note

The item numbers in the illustrations refer to the installation kit overview.

All items marked with upper case letters refer to the overview, wiring harness for navigation.

All parts not included in the installation kit are identified with lower-case letters.

These installation instructions apply only to vehicles which are equipped with the on-board monitor (SA602).

Subject to technical modifications.

Tools and auxiliaries required

Screwdriver for slotted head screws
Inspection lamp
1/4 inch reversible ratchet
1/4 inch socket wrench insert WAF 8 mm
Screwdriver for cross-recessed head screws
Multipurpose knife
1/4 inch extension piece
Side cutters

Contents

Section

  1. Preparatory Work
  2. Overview, Installation Kit
  3. Overview, Wiring Harness for Navigation
  4. Installing Wiring Harness for Navigation
  5. Cutting Trim Panel for Subwoofer (only vehicles with BMW HiFi system Professional DSP)
  6. Installing CD Computer
  7. Encoding

1. Preparatory Work

Print out defect code memory. Disconnect battery.

Remove luggage compartment floor cover. Remove left luggage compartment trim panels. Remove luggage compartment partition trim panel. Remove subwoofer trim panel and subwoofer (only vehicles with BMW HiFi system Professional DSP)

2. Overview, Installation Kit

F 39 65 181 M

Navigation System Japan BMW 5 Series E39

Item Description Quantity
1

 

2

Navigation CD computer (provided in Japan) 1
 

Wiring harness for navigation

 

1

3 GPS receiver (provided in Japan) 1
4 Holder for navigation computer 1
5 Cable duct 1
6 Expanding nut 4.8 4
7 Hexagon self-tapping screw with washer 4.8 x 16 6
8 Cable tie 2
9 Expanding rivet 1
10 CD-ROM road map (provided in Japan) ——

1

2. Overview, Wiring Harness for Navigation

F 39 65 182 M

Item Version/description Connection location in vehicle Designation/ plug-in slot
A 20-pin socket housing/navigation A Navigation CD computer A 112 in luggage compartment X1312
B 7-pin socket housing/GPS receiver GPS receiver N28 in luggage compartment X1958
C 6-pin white socket housing/STVB HiFi/KBB At tied-back 6-pin white pin housing in left of luggage compartment X1716
D 10-pin black socket housing/video module II Video module A 197 in luggage compartment X18804

4. Installing Wiring Harness for Navigation

F 39 65 183 M

Navigation System Japan BMW 5 Series E39

Connect branch D to 10-pin black pin housing X1 8804 (f) at holder for video module.

Route wiring harness for navigation along the audio wiring harness to C-pillar reinforcement and secure with cable clips (e) and cable ties (d and 8). Connect branch C to tied-back 6-pin white pin housing (a) and tie back on main vehicle wiring harness with cable tie provided.

Release cable tie (b).

Install trim panels in luggage compartment and pass GPS antenna line with branches A and B through the aperture in the left-hand luggage compartment trim panel forward to top of luggage compartment partition.

5. Cutting Trim Panel for Subwoofer (only vehicles with BMW HiFi system Professional DSP)

F 39 65 183 M

Navigation System Japan BMW 5 Series E39

Cut trim panel (a) for subwoofer as shown in illustration.

Dimension b = 68 mm
Dimension c = 68 mm
Dimension d = 72 mm
Dimension e = 72 mm
Dimension f = 30 mm
Dimension g = 65 mm

Install subwoofer.

Note

Take particular care when installing the trim panel to ensure that no cables are trapped .

Run the GPS antenna line and branches A and B of

the navigation wiring harness in the clearance between the trim panel and subwoofer to the cut-out for the navigation computer and install cover .

6. Installing CD Computer

F 39 65 184 M

Navigation System Japan BMW 5 Series E39

Press expanding nuts (6) in holes (b) provided in the top of luggage compartment partition (a).

Fit hexagon self-tapping screws (7) in front expanding nuts (6) and screw in leaving approx. 6 mm.

Unclip and disconnect luggage compartment light and pull out connection cable as far as possible.

F 39 65 185 M

Navigation System Japan BMW 5 Series E39

Important!

Take particular care during installation to ensure that no cables are trapped.

All vehicles

Connect branch B and plug connector (a) of GPS antenna line to GPS receiver (3) .

Fit GPS receiver (3) in holder (4) and secure with hexagon self-tapping screws (7).

Fit branch A in holder (4) and secure with cable clips (D .

Run connection cable (c) for the luggage compartment light through the aperture for the luggage compartment light on holder (4) and branch A through the cut-out for navigation CD computer (1) on holder (4) .

Fit holder (4) with guides (d) in preassembled hexagon self-tapping screws at the top of the luggage compartment partition and secure with the hexagon self-tapping screws provided through the holes (e).

Firmly tighten all four hexagon self-tapping screws.

Connect luggage compartment light (b) to connection cable (c) from vehicle wiring harness and clip in aperture in holder (4).

Connect branch A to navigation CD computer (1) and fit navigation CD computer (1) in holder (4).

Only vehicles without BMW HiFi system Professional DSP

Fit cable duct (5) in cut-out of left-hand luggage

compartment trim panel.

Fit navigation wiring harness and GPS antenna line in cable duct and close strap (g).

Place cable duct (5) on holder (4) for navigation computer and secure with expanding rivet (9).

Reassemble vehicle in reverse order of removal.

7. Encoding

The system requires encoding.

To ensure the retrofit system

is operable to its full extent

does not cause malfunctions and interference in association with the other electrical vehicle systems, these systems and, if necessary, other vehicle control units must be encoded.

It is additionally stored in the central encoding code of the IKE.

This encoding procedure is carried out automatically with the current encoding program in the “retrofit” path. The procedure is user-prompted, the relevant text information must be observed while implementing the individual steps.

This retrofit encoding is available for this product as of version C7.0.

Procedure:

Connect DIS/ MoDiC to vehicle Ignition “ON”

Selection “Encoding ZCS”

Confirm date entry with “Y” (for MoDiC only) Series: “E39”

Path: “2 Retrofit”

System: “7 Navigation”

Start automatic encoding (confirm with “Y”)

Ignition “OFF”, wait at least 10 seconds and switch ignition “ON” again

Have encoding label printed out and adhere over existing encoding label in right-hand side of luggage compartment on frame side member next to battery.

Print out defect code memory.

Insert CD-ROM road map in navigation computer. Calibrate navigation system in accordance with instructions.

Carry out function test.

banner